Pulsed laser deposition of YSZ electrolyte layer obtained by hot pressing of the target

Authors

  • А.G. Umirzakov "Physico-Technical Institute" LTD, Almaty, Kazakhstan
  • A.L. Mereke "Physico-Technical Institute" LTD, Almaty, Kazakhstan
  • R.E. Beisenov "Physico-Technical Institute" LTD, Almaty, Kazakhstan
  • D.A. Muratov "Physico-Technical Institute" LTD, Almaty, Kazakhstan
  • B.A. Rakymetov "Physico-Technical Institute" LTD, Almaty, Kazakhstan
        85 37

Keywords:

hydrogen energy, thin-film solid oxide fuel cell, electrolyte, hot pressing

Abstract

The article describes a technique of the hot pressing yttrium stabilized zirconium target for use in a pulsed laser deposition of the electrolyte layer for solid oxide fuel cells. Hot pressed target made of zirconium stabilized with yttrium percentage of ZrO2 and Y2O3 components are 92:8%. It is shown analytical studies and the results of the parameters of obtained target and deposited electrolytic layer on the silicon substrate (SEM, AFM, EDX). Scientific work aimed at solving urgent problems to reduce the operating temperature of solid oxide fuel cells from 850 - 1000 °C to 400 - 550 °C, which is achievable, as the results of research, with a decrease of the electrolyte thickness layer deposited thin-film technology and ultra-thin electrolyte deposited for the purpose of reducing the operating temperature, the size and weight of the fuel cell. Morphology studies showed the formation of a rough surface. Elemental analysis of the deposited YSZ electrolyte layer revealed an 8% of yttrium content in the structure, and zirconium was half as much.

References

1 Lynd L.R., Cushman J.H., Nichols R.J. Wyman CE: Fuel ethanol from cellulosic biomass // Science. – 1991. – Vol.25. – P.1318–1323.
2 Wang M.Q., Huang H.-S. A full fuel-cycle analysis of energy and emissions impacts of transportation fuels produced from natural gas. – Argonne, Illinois: Center for Transportation Research Argonne National Laboratory, 1999.
3 Kordesch K.V., Simader G.R: Environmental impact of fuel cell technology // Chem Rev – 1995. – Vol. 95(1). – P.191–207.
4 Eon Woo Park, Hwan Moon, Moon-soo Park, Sang Hoon Hyun. Fabrication and characterization of Cu–Ni–YSZ SOFC anodes for direct use of methane via Cu-electroplating // International journal of hydrogen energy. – 2009. – Vol. 34. – P.5537–5545.
5 Ignatiev A., Issova A., Eleuov M. Nanostructured Thin-Film Solid Oxide Fuel Cells // Chemical Bulletin of KazNU. – 2011. – №3 (63). – P.5432.

References
1 L.R. Lynd, J.H. Cushman, R.J. Nichols, C.E. Wyman, Science, 25, 1318–1323, (1991).
2 M.Q. Wang, H.S. Huang, A full fuel-cycle analysis of energy and emissions impacts of transportation fuels produced from natural gas. – Argonne, Illinois: Center for Transportation Research Argonne National Laboratory, 1999.
3 K.V. Kordesch, G.R. Simader, Chem Rev., 95(1), 191–207, (1995).
4 Eon Woo Park, Hwan Moon, Moon-soo Park, Sang Hoon Hyun, International journal of hydrogen energy, 34, 5537–5545, (2009).
5 A. Ignatiev, A. Issova, M. Eleuov, Chemical Bulletin of KazNU, 3(63), 5432, (2011).

Downloads

How to Cite

Umirzakov А., Mereke, A., Beisenov, R., Muratov, D., & Rakymetov, B. (2018). Pulsed laser deposition of YSZ electrolyte layer obtained by hot pressing of the target. Recent Contributions to Physics (Rec.Contr.Phys.), 60(1), 82–87. Retrieved from https://bph.kaznu.kz/index.php/zhuzhu/article/view/516

Issue

Section

Condensed Matter Physics and Materials Science Problems. NanoScience